Showing all 2 results
When will the humidity LEAVE!!! Was in Iraq and despite the dust almost every single night was 9 on a scale to 10
Thanks for sharing the pics of your Observatory. My husband is so into this stuff, I had bought him a little telescope a few years back and we will try to get out back when things are going on, but his scope is not like yours. He was amazed at the pics you had taken, again thanks for sharing.
Tim & Peggy Doherty
Thanks for the useful tips. I look forward to using them on my trip.
My brother owns a ranch bordering the east city limits of Burnet, TX where I keep an 8″ dob to use when I visit. I have also observed and spoken at the Eagle Eye Observatory on Lake Buchannan where the light pollution is not as great. Hope the Orion Ranch is west of Llano. The skies get incredibly dark about 10 miles west of Llano!
Thanks. Actually, it’s in the Bertram area, which is about 10 miles East of Burnet. Pretty much surrounded by light pollution, but still better than closer in to Austin!
Hello from Québec !
I have a nexstar 8se and I take pictures of the sun ,the moon ,the planets.
I would like to go further and give a try with deep sky imaging ,but I dont have any reference photos and datas…from other 8se owners!
My scope is on an heavy duty wedge !
I see someone has a set up with an 8se. can I see some pics and some datas from that
thank you !
Hey Maxx, welcome! Check out this link for most of what you’re looking for. There are a couple other links from there. Good Luck!
Excellent article, Michael. Thank you for clarifying this with a real test showing how voltage can spike well above a power supply’s rated output.
OPT is the nicest brick and morter telescope shop I’ve ever been in .
The Obsevatory in Texas looks like a nice one from the ads I’ve seen , but it’s been long ago that I’ve been to Texas .
I know I’m two years late to the party, but this was highly educational. Thank you!
Thanks for posting the pictures; very handy to know what to expect prior to disassembly. Also interesting to note the improved AZ drive compared to the original CPC.
The Dec drive motor on my CPC bounces around like yours and sometimes makes a ticking sound as it hits the metal arm.
Thank you for the great detailed description, have you had a chance to run it in anger yet? I have not seen any follow up, I would be very interested in knowing the result of the work, my initial thoughts had been why on earth would you do this to such and expensive bit of kit, how can you possibly improve on the manufacturers efforts, surly they would have used a mix of bearing materials through the results of trials and testing? But having seen the insides, care of yourself, I was surprised to see some parts that appeared to be “not the best” quality, I know everything is made to a cost, but it does make me wonder now, my CPC1100HD cost what I thought was a lot, I sort of expected a bit better. I have had mine a year or so but not had much time on it, the little that I have, have had tracking issues with photography, more likely to be my setting up, but doubt is creeping in.
One heck of an observatory! There must be loads of us out here thinking “if only!” Fantastic, Cheers, Ian.
So far it seems to be running fine. The azimuth/RA axis runs smoothly under the full load of the wedge. I’m still debating whether to go into the declination axis again and tighten the spring so that the gear can’t slip teeth at all. If I don’t run perfectly balanced, it will easily skip at the moment. I’m not sure which is better, risking damage from slipping teeth, or damage from not being able to slip teeth!
I purchased a 11 cpc hd which would not connect to sky portal then the dec would not stop so I have sent back the 3rd scope to dealer. Each scope had a whining sound coming from the motor board. One scope actually heated up where the plug board is and all had this hissing sound. what do you think is this problem?
A whining sound from a power supply is usually due to an inductor that is being driven at a high frequency. It’s basically a coil of wire on a magnetic core, and like a transformer, can make noise if the individual wires are able to move at all under the stress. It’s basically the equivalent a really bad speaker. Normally that’s nothing to worry about, but it sounds like you’ve been having more than your share of problems.
Pingback: Best Grease for Nexstar / CPC According to Super Lube Expert
Wow, your testing, review and explanation of your experience these products is amazing. Well done and thank you.
Great information, thanks for all your work.
We stayed in Ord the night before — about 45 minutes north of Ravenna. Left early Monday morning thinking there might be heavy traffic, but it seems the heavy traffic was from the south on I-80. We had considered heading farther west, but glad we did not. The viewing from the winery was great.
You were a great asset for our viewing pleasure in Ravenna! Can’t wait to see the rest of your photos.
We are so appreciative of your help and expertise! We know it was a long and wild ride all weekend, but you’re right, it was totally worth it! What an experience! Thanks again for spending your time with us at Cedar Hills Vineyard & Gardens!
I’m even later to the party, but I agree – fantastic information! How do we fight it ? Possibly capacitors in the 0.1 uF or less range ? Reversed biased diodes ? Interesting questions…
I have the same ZWO camera that I want to use for an All-Sky camera. Are you CAD files available so I might make a similar setup?
I need to make some tweaks, but I’ll likely make the STL files available in the store for a nominal fee.
How can I send you a sample of my camera-generated 3-D star fields?
Send to info at…
Are you making these for tripods with 2″ legs?
Good timing! I’m actually working on a design for the NexStar GPS tripods. I’ll send you some information by e-mail.
Good work, not easy to implement all this! I’ve been following this in the ASCOM Yahoo group a bit and it didn’t sound like a straightforward job…
This video was super cool Michael! Thanks for sharing…
Are you selling any of your 3D printed parts? I have an 8SE and would like to purchase your hand controller mounting bracket.
Sure, I can print one for you. I want to tweak the mount part a bit as it doesn’t really need that big flare on the ends. I’m planning to spend some time getting more items listed in the store.
$20.00Add to cart
$35.00Add to cart
$200.00Add to cart
$60.00 – $100.00Select options
$20.00 – $35.00Select options
$1.00Add to cart
$5.00Add to cart