Arduino GPS Replacement for NexStar GPS

Ok, after lots of research and experimentation, I’ve completed my Arduino Nano based GPS for replacing the NexStar GPS modules.  I’m going to give a detailed walk through of everything here so that it’s well documented, although it may take a few posts due to the picture limits per post.  I started from Barry’s repository on GitHub because he was doing the same mount and I didn’t need the display that others have added.  However, what I didn’t realize until I was part way through everything that the firmware there was incomplete and never actually worked.  Thus I had to merge some of Miro’s (ForestTree) fork back into my code to complete everything.  There are two main changes I made.  The first was to fix the serial interface so that it works as Celestron intends it to without any additional hardware (no diodes, etc.).  It also uses the busy control line like it’s supposed to.  The second was to add support for the GNSS NMEA sentences so that it responds to the $GNxxx sentences that the BN-220 generates when GLONASS satellites are visible, as well as the $GPxxx sentences from straight GPS.  I’ve created a fork from Miro’s version at https://github.com/L…ulf/nexstar_gps.  The way I uploaded it did a full replace on the .ino and isn’t giving a proper difference view, but I didn’t want to fool with figuring out how to fix it.  If someone wants to give me an easy way, I’ll see about doing so, but there are plenty of other difference viewers you can use.  

 

Barry’s wiring description wasn’t very clear on the wiring to the telescope, so I had to reverse engineer the NXW434 PIC microcontroller board that the Arduino is replacing.  

This connects to the NXW249 GPS bpard:

which coupled with the active GPS antenna makes up the parts being replaced by the BN-220.

I created a schematic for the NXW434 and posted it in my repository. 

For reference, I also opened up my CN16 and found the exact same circuit combinations.  You can see the blue AUX serial connector on the right and the white GPS connector in front. The newer CPC style GPS module is under the antenna similar to the BN-220. Two Microchip 12F629 PICs identical to that on the NXW434 provide the serial interface.  The PIC with the red dot is the equivalent of the NSW434, while the one with the blue dot runs the compass and level (long clear tube with a metal ball in it) at the back.  Those latter components are elsewhere in the NexStar GPS. 

Rather than removing the NexStar GPS from the observatory, I rigged up a voltage regulator so I could plug the NXW434 into my NexStar 8SE mount. (Ignore all the other chips stored on the breadboard.  They’re just stored there from old projects!)  This allowed me to hook up my oscilloscope so I could monitor the communication and confirm what each pin was actually doing.

So what I had already suspected, then determined with the oscilloscope and finally confirmed looking at the CN16 wiring, is that the four wire interface on the NXW434 is 5V power, ground, the drop/busy line, and a combined TX/RX line.  It’s NOT separate TX and RX lines as you might think from Barry’s repository.  That’s why Miro’s AVX design works with a single wire.  It turns out the hand controller still reads the GPS fine without the busy line being pulled low.  It’s just that anything else (e.g. a serial or Wi-Fi interface) could potentially attempt to access the interface at the same time and cause a collision since the busy line isn’t low.

Here’s my Arduino GPS on the test jig.  The BN-220 GNSS module on the left is connected to the Arduino Nano on the right. The jumper temporarily connects serial TX and RX pins, while allowing me to disconnect and reconnect the USB serial port for programming.  

A look at the back side shows more modifications.  The resistors in the middle had to be removed because they connect the CH430 (or FT232) to the serial port on the Atmel ATmega processor. (Funny that Atmel was bought by Microchip who makes the PIC processors!) The resistors are relatively low values, but enough so that if you hook up a normal serial TTL connection to the Atmega you can still drive the lines high or low against the signal from the USB to serial adapter.  However, if you were to leave them on and connect to the common buss on the NexStars, they’d still drive the line and cause Error 16 and 17 when the hand controller starts up and tries to talk to the motor controller.  However, I still needed jumpers for debugging, and started with them on the surface mount pads, but they pulled off quickly. Now they’re directly on the pins.  Of course this same arrangement could have been used with an external USB adapter, or you could use an Ardunio mini with separate adapter like Miro’s setup.

Here’s a closeup of the wiring after removing all the jumpers (after programming it first!).  As you can see, no additional circuitry is required.  The schematic for this setup can be found here.  Note that I might have rearranged the location of the drop line vs. the GPS software serial port had I not already soldered up the GPS connection to match that of the previous designs.

On the back side you can see the solder bridge between TX and RX after removing the jumpers.

I’ll add picture of the installation later, but the BN-220 module with attach directly on the double-stick tape that I pulled the active GPS antenna off of.

The Arduino and wire will then route down to the connector at the bottom of the fork arm.

Note that the exact same firmware and circuit board setup can be used to connect to the AUX port on any Celestron mount.  Simply feed the +12V line into the Vin pin of the Arduino Nano.  You can find the schematic in my repository here.  At this point I’m debating turning my NexStar 8SE into the (presumably) first NexStar GPS 8SE, adding this mod internally.  That way I don’t have to fool with the CN16 anymore.

I’ll be posting a video of the testing when I have the chance, but here’s a screen shot from the oscilloscope.  This is showing a transaction between the hand controller and motor control board.  The top trace is the serial communication.  The bottom is the drop line, presumably named that because you drop it low to indicate busy.  

After installing the upgrade in my NexStar GPS, this is what it looks like.

I attached the GPS module directly to the previous sticky tape and used a tie-wrap pad to attach the Arduino nearby. I had made more than enough cable to reach the connector, but went ahead and left it long, which meant bundling at the end with another tie wrap sticky pad. I went ahead and routed behind the arm like the RF cable had run to the old GPS module.

The modification works fine, although I can actually see the blue GPS LED shining through cracks in the case, so I might get in there and cover it up someday.  

I also decided to order another BN-220 and quickly built an internal GPS modification for my 8SE. Works great! I would hazard a guess that this is the world’s first NexStar GPS 8SE! 

I created a jumper to tap in to the hand control connector on the serial board so that I didn’t have to modify any of the internal parts.

The body of the arm is all metal, so I had to install the GPS in the base, but it works fine there.

At any rate, hopefully all this will help others who want to make this mod.  

Posted in Uncategorized | 2 Comments

Upgrade Complete!

We’re now running on the latest versions of Gallery 3, PHP, and WordPress, and everything seems to be working fine. There are some glitches in a couple of Gallery modules, but none that appear to affect the user experience. I’ll work on fixing those in the background in the coming weeks. Enjoy the website!

Posted in Uncategorized | Leave a comment

Upgrading Photo Gallery

Well, it’s been a long time coming, but I’m going to bite the bullet and upgrade my Gallery 3 based photo gallery V3.09 to the new “Gallery Revival” V3.10. In 2015, the development on the Gallery 3 project (galleryproject.org) ended and the support site was locked down. In an effort to maintain support for users like myself who were happy with Gallery 3 but needed to make tweaks and enhancements, I started the Gallery 3 Yahoo group. This has helped numerous users keep their Gallery 3 installations plugging along, but web technology, security issues, and the like have changed the environment considerably since the Gallery 3 development project was started many years ago. Thankfully, at the beginning of this year, an industrious member of the Yahoo group released a new version of the Gallery software that brings it up to date with some of the latest web functions. If all goes well, it won’t change the way anything works from the user side, but from the web server, it will allow running the latest, safest version of all server software. So, I plan to make the migration “as soon as I can.” It shouldn’t take long once I get started, but if I don’t get started this evening, it might be a few days before I get to it. At any rate, I’ll post again when the change has been made. Let me know if you encounter any problems!

Posted in Uncategorized | Leave a comment

Visit my YouTube channel!

I finally gave in and started my own YouTube channel for various videos I’ve been putting together. While I’ve typically done photographic records that I could come back and document with text, I found I wasn’t doing that very often, even though I had tons of pictures available. Since the public trend is toward video “how-to” guides, with the recent purchase of a large 3D printer kit that was not documented properly at release, I decided to try my hand at video logs instead of just photographic logs. They may be a bit rough, and editing still takes just as long as documenting a bunch of photos, but they’re a start. The only downside is that my photographic documentation of some of these projects has suffered due to the concentration on video.

At any rate, I’ve set up my YouTube channel at the previous link and moved a couple of my astronomy videos there, along with other videos on the 3D printer and other topics. I’ll probably still upload appropriate videos here in parallel, but please take a look and subscribe if you’re interested.

Thanks,

Michael

Posted in Uncategorized | Leave a comment

Dyson’s Radio, Free from Friday through Sunday, February 24th, 2019

See the previous post for details on the book. For some reason the originally scheduled sale on Wednesday didn’t fire.

Posted in Uncategorized | Leave a comment

Published My First eBook!

When an amateur astronomer detects a modulated signal in the flash of a nova burst, the race is on to capture and decode the signal before it’s too late.

This science fiction short story is my first self-published eBook through Amazon, although it’s not my first sci-fi short story.  Of course I’ve written plenty of technical magazine articles and papers, not to mention untold numbers of online posts, articles, how-tos, etc., but fiction is something that, beyond not just having time to write, I never felt I could dedicate the time to it, much less carry a story to completion.  Thus, the most I’ve been willing to shoot for is a couple of short stories.

Leaving out some stories I wrote back in high school and college that I’d love to dust off if I could find them, my first relatively contemporary short story was “Goodbye Mr. Smith”, a sad and extremely short story from a sad time in my life, that surprisingly has components in common with the end of Dyson’s Radio.  In “A Dark Matter”  (currently awaiting a response from Analog)  I discovered a narrative approach that worked well for me.  Thus, when I came up with the idea for Dyson’s Radio, I knew exactly what I needed to say and where I needed to end up.  However, even I didn’t know everything I’d discover along the way.  The story ended up being quite a bit longer than I expected.  It also became so current and topical that I decided it couldn’t wait for a long editorial review process.  After a quick response from Asimov saying they wouldn’t be able to do it in time, I decided to go for direct publication to be sure that people had a chance to read it as it was intended to be experienced.

While I could easily have padded the story considerably by explaining many of the things mentioned, it was really written for the true space geeks among us who will immediately understand most of the references that the characters already know.  Thus, if you’re here it’s probably because you already love the idea of space and space exploration and don’t need anyone talking down to you about it.  However, there is a tremendous amount of background information I put together to keep the story plausible, and I envision writing a technical article on “Building Dyson’s Radio” to be published sometime in the future.  And who knows.  If I get brave enough I may even revisit this world.  There’s certainly plenty to build on, but I just don’t know if I’m up to the challenge!

And if you’re lucky enough to be reading this today (December 6th, 2018), it’s currently free on Amazon.  Merry Christmas!

Posted in Uncategorized | Leave a comment

I think I’m done!

I started writing this post just over a year ago and then realized I wasn’t done, so I didn’t get much further than a title and a first line that I tossed.  However, at this point I think I’m about as done as I’m going to get with processing of images related to last year’s solar eclipse.  I’d originally intended to design another poster or two, but at the moment I have too many other things going on and don’t feel all that creative in that direction.  Perhaps before the next total eclipse rolls around in 2024 I’ll go back and look at it again.

At any rate, what I have accomplished just recently was to finally go back and finish a process I’d started last year when I discovered I’d captured the amazing lunar umbra shadow on the clouds in the following image.  Since I apparently never made a blog post on THAT I’ll post it here too.  In fact, it turns out that I never posted much of anything here about all the processed images from the eclipse, but I did make a few posts on Cloudy Nights.

So you can see all my images and time lapse video from the event, and details on the preparations and photography of the actual eclipse, but the one thing that took me quite a while to do (and even longer to go back and finish) was manually recording the automatic exposure settings of every frame of my time lapse video and then writing a script to adjust the exposure to back those out of each frame in Photoshop so that it’s as though the camera was set with a fixed exposure during the entire eclipse.  While no computer monitor or file format is sufficient to cover the real dynamic range from full sunlight to evening night sky, this video will give you an idea of the change in illumination throughout the duration of the eclipse.  The bright sky is completely blown out, but if you watch the landscape and foreground you can see things getting darker during the progression of the partial eclipse before things go almost completely black at totality.  The goal is to give you an idea of what totality really felt like.  Note you can still see the shadow of the moon against the sunlit clouds along the horizon.  There are two versions of this in the solar eclipse party folder linked above, but this one has the actual eclipse progression overlaid in the corner once the image capturing starts at about 30 seconds into the video.  You can compare the darkening of the sky to the progress of the Moon across the Sun.  I hope you enjoy it!

 

Posted in Uncategorized | 1 Comment

NexStarEquatorial Driver Released for Testing

In my ongoing quest to fully automate my observatory, I’ve been developing a number of ASCOM standard drivers for most of my custom equipment. The one thing I’ve wanted to do for some time is to find an alternative to Celestron’s NexRemote software that has to be manually started and brought out of hibernation and then manually put into hibernation and shut down before powering off the telescope. Even then, it was common for the NexRemote software to hang up and lose alignment often requiring a good half an hour or more to attempt to re-do an alignment remotely.  It never made sense to me that with the availability of plate solving to determine exactly where the telescope OTA was pointing that I couldn’t just enter the current coordinates and have the scope aligned, given a good polar alignment of the mount.

What I needed was a software/driver that would automatically restore the motor position information on startup and automatically stop the drive and save the position information  on shutdown.  Not to mention, having the ability to take a picture and quickly align the mount to the current RA/DEC coordinates.  Given that there was no other alternative forthcoming, I finally decide to go ahead and develop my own solution.  Rather than writing another stand-alone program to take the place of NexRemote, which is just an emulator that runs standard hand control firmware, it made more sense just to build all the required functionality from the hand controller into a single telescope interface driver that could be used by any software built to use the ASCOM standard.  Thus was born the NexStarEquatorial ASCOM driver.

Essentially I’ve implemented the important components of a NexStar hand controller directly into an ASCOM driver that communicates with the motor controllers directly through the PC or AUX port of the mount.  Alternatively, the driver also supports communication through the serial port adapter in the base of the NexStar hand controller, although like NexRemote, it does not actually use the hand controller for anything other than the interface.  The driver automatically saves and restores the current position of the mount on exit so that even if the mount is powered down in between sessions, when the driver starts back up, everything’s still where it was.

This driver is targeted towards full system automation and imaging, so it only supports the NexStar mounts in equatorial mode (thus the name).  It also relies heavily on imaging software capable of plate solving and aligning automatically (i.e. something like Sequence Generator Pro).  With a good polar alignment and starting point, there’s no need to do any sort of manual alignment at all, but it does support manual entry of coordinates from a plate solve to get the current reference if desired.  I actually don’t use it because SGP handles that all for me.

By limiting the functionality to equatorial mounted scopes , including German Equatorial Mounts (GEMs) like the CGE, CGEM, CGE Pro, etc., and fork mounted telescopes like the NexStar GPS and CPC mounted on polar wedges, the requirements for the driver are greatly simplified.  For a mount that’s perfectly polar aligned, the “azimuth” axis becomes the right ascension (RA) axis and simply needs to run as a clock motor, with one revolution every 24 hours.  The other axis (altitude/elevation for a fork mount) just provides the North/South declination adjustment.  The spherical coordinate system for an equatorial mounted scope is pretty straightforward then, with the current local sidereal time indicating what should be directly overhead along the meridian line dividing the eastern and western halves of the sky.  The azimuth angle relative to the meridian just needs to be converted from 360 degrees to a 24 hour format and offset by that sidereal time to get the current right ascension, although for GEM mounts that also requires an east/west offset of 90 degrees between the axis position and the orientation of the OTA.  The declination axis runs ±90° from the equator, but again for a GEM there’s a positive and negative side to the OTA orientation depending on which side of the pier the OTA is on and which side of the sky it points to.  And of course in the southern hemisphere, the scope is mounted in the opposite direction and all axes have to run backwards.  In all it’s just a pretty basic spherical geometry problem, but getting all the signs and combinations of behavior correct was still a bit tricky.  Some of the Celestron mounts have their own quirks as well, with the CGE Pro (and possibly others) forcing a required 90 degree offset to the definition of “up” on the azimuth axis.  And of course the ASCOM standard has its own quirks.

The following figure is the current setup dialog for configuring the driver.  It sets up the communication method and mount type, as well as the mount location which is critical to the initial determination of the RA/DEC coordinate system.  Subsequent homing and alignment/synchronization steps will set the actual position offsets once connected to the scope.  In addition, ASCOM reports the details on the optical tube assembly, so that information can be entered here as well.  Hovering over each control provides hints as to the function of each setting.

Once the ASCOM compliant client software connects to the scope through the driver, the following hand control paddle is displayed.  The hand controller can be toggled to stay on top or closed and reopened from ORO logo icon in the system tray.  The hand control provides traditional manual positioning control, targeting, position readout, tracking and parking control, as well as basic alignment functions.  No positioning database is provided as that is expected to come from the client software.  Other than an initial homing process to set the reference position of the mount the first time the driver is used, no further manual interaction should be required given suitable client software.

The driver has been made available for beta testing by interested users, and I’ve started this thread on Cloudy Nights for comments and feedback.  I may eventually publish a more detailed manual here in the future, and of course expect to probably add a few more features over time as I have time and the desire to do so.  I hope others will find this as useful as I have so far.  It solves my automation problem amazingly well!

Posted in Uncategorized | 6 Comments

Upgrading my Autoguider Camera

As we progressed through another galaxy season, I was constantly fighting to find a guide star that keeps my target framed.  With my remote controlled off-axis guider (OAG) setup, if I can’t find a good star in the guide camera field of view (FOV) when the target is centered, my only option to shift the entire image position looking for a star, since I can’t rotate or otherwise move the guide camera relative to the target FOV.  Thus I started thinking about upgrading from my QHY5L-II M to a new guide camera, ideally with both a larger FOV and higher sensitivity.  Looking at the new crop of guide cameras, this led me to looking at cameras based on the Sony Starvis (star visibility) IMX178 sensor.  Comparing with the MT9M034 sensor in the QHY5L-II, the IMX178 sensor has just over twice the total area (7.4 x 5 mm vs. 4.8 x 3.6 mm or 2.09x), but with 5x the pixel count.  In addition to improving my guiding, another advantage to this 6.3 MP camera is that it would be a reasonable entry-level imager for narrow band imaging (e.g. H-alpha solar imaging, etc.).

After some online discussions with others on Cloudy Nights and elsewhere, but otherwise very little feedback on the best choice for my application, I ended up putting together a comparison table between the monochrome sensors currently being targeted for guide cameras.  The following table is in order of increasing price.  The IMX290 sensor has the best sensitivity in the new Starvis line, but with the 1080P 16×9 form factor, it suffers the same limitations I discovered when I tried using the ZWO ASI290MC for my all sky camera.  It basically has the same area as the QHY5L-II, but with a less practical form factor (16×9 vs 4×3), so while I’d expect the sensitivity to help considerably, it wouldn’t increase the usable FOV.  On the other hand, the IMX174 is a much bigger sensor, which presumably explains why cameras based on it are considerably more expensive, but it’s also based on older technology and has a much lower resolution.  By simple virtue of the large pixel size, it can be expected to be more sensitive than the QHY5L-II, but the potential loss in guider resolution, not to mention the much higher cost, make this an impractical solution.

MT9M034 IMX290 IMX178 IMX174
Size (mm) 4.8 x 3.6 5.61 x 3.18 7.37 x 4.92  11.34 x 7.13
Relative Area 1x 1.03x 2.1x  4.7x
Pixel Size (μm) 3.75  2.9 2.4 5.86
Relative Pixel Area 1x  0.60x 0.41x 2.44x
Pixel Count (WxH) 1920 x 960  1936 x 1096 3072 x 2048 1936 x 1216
Total Pixels (MegaPixels) 1.2  2.1  6.3 2.4
Relative Pixel Count 1x 1.7x 5.1x 1.9x

That really just leaves the original IMX178 I started looking at, which also happens to be the color sensor in the ZWO ASI178MC I finally integrated into my all sky camera.  That just took me back to the original choice I was trying to decide between which camera vendor to use, QHY or ZWO.  My imaging camera and previous guider are QHY, but I tried ZWO for the all sky camera, partly due to a better overall price point.  However, the other factor here was the camera form factor.  While both QHY and ZWO make cameras in the mini guide camera form factor, for this particular sensor, only QHY made a mini similar to the QHY5L-II I was replacing.  For ZWO I’d have had to go with the same form factor as the all sky camera.  While that’s essentially the same form factor as the StarShoot AG I’d been using before the QHY5L-II, I had reason to want to stay with the mini form factor, for weight if nothing else.  Thus, even though it was about 10% more expensive I chose to go with the QHY5LIII178M over the ZWO ASI178MM.  Only after receiving my new camera did I finally get some feedback from someone that the QHY version has better fixed pattern noise due to some additional circuitry QHY adds!  Hopefully that justifies the added cost.




Unpacking

I ended up ordering from High Point Scientific simply because they had it in stock and OPT didn’t.  Both were running the same 5% NEAF discount on top of QHY’s NEAF sale.  High Point shipped it after one business day by USPS and it arrived two days later.   High Point was also asking customers to create unboxing videos, so this is the first time I’ve attempted to capture video footage in addition to photos of the process.

The camera arrived nicely packaged in a “collector can” similar to that for the QHY5L-II.

The camera is a nice pretty blue anodized package.

The connector end of the camera has a USB 3.0-B style connector and a non-standard LEMO connector for the guide port due to the limited space.  Given the compromise ZWO was making for this form factor by going to a micro USB 2.0 interface, I’d much rather have a USB-B connector than a USB 3.0 micro connector and a standard RJ-11 socket for the guide port.

I didn’t get the best of focus, but here’s my attempt o compare the size of the two sensors.  You can see how much bigger the new IMX178 sensor is. The distance from the tube front appears the same, so adjusting the confocal ring on the new camera to the same distance from the front of the nosepiece had it almost perfectly focused when I put it into the OAG.

Here it is installed on the OAG.  I forgot to take the picture while I was using it, so this was after parking.  I definitely need to work on cleaning up my cables!




 

 Sensitivity and FOV Testing

Before swapping cameras, I did a few tests to try to get an idea of the relative sensitivity of the two cameras.  With the exception of the IMX290 and IMX178, which are in the same Starvis series, there was precious little comparable sensitivity data for the sensors, so this was the first chance to find out if I really gained anything in sensor sensitivity.  I’d previously been imaging M81 and knew I had one good guide star visible there with the QHY5L-II.  At one second exposure, that single star is visible in the FOV.

At five seconds, a second star is visible if I adjust the gamma to pull it out of the background.

That’s really the limit of usable guide star exposure length, but doubling it to ten seconds didn’t change anything.  Swapping to the QHY5LIII178M, that first star is clearly visible at 0.2 second exposure.  The star profile is a bit noisy, but part of that is because the camera’s not perfectly focused at this point.  You can see how tiny the star is given PHD2 shows the entire FOV, so the scale here is smaller due to the much higher resolution.

At one second, the second star becomes visible.  This image also gives you an idea of how much larger the overall FOV has become.

At two seconds a third star becomes visible, although it’s easier to see in this four second exposure.

At this point there’s some background noise becoming visible and the image became unusable at a five second exposure.  In hindsight I believe this was due to having left the observatory monitoring cameras enabled so that their IR lights were creating a strong background lighting.  I may add some new test images to the gallery later, but the general observation is that despite the smaller pixel size, the QHY5LIII178M is at least five times more sensitive than the QHY5L-II.  From Sony’s documentation, the IMX290 is twice as sensitive as the IMX178, but at that point chances are good I would be sky glow limited in some cases!

Hopefully this will help anyone else researching a new autoguider camera.  For more information, you can check out these threads on Cloudy Nights and the PHD2 forum.

Posted in Uncategorized | Leave a comment

A Sad Day for TXMOST!

Today was a sad day for the Texas Museum of Science and Technology as the temporary location in Cedar Park closed its doors.  It would have been a great day had that been due to moving into a permanent facility, but given the absurdly high cost of the lease on the old indoor soccer building (that just had a dirt floor until six months or so ago) it was costing about $50k a month in donations just to keep the doors open.  Due to that and some lingering financial consequences of some of the initial exhibits like the incredibly expensive Body Worlds that they opened with, in January the museum Board of Directors chose not to renew their lease and instead focus their efforts and any incoming donations on their permanent location.

On Friday night we had our final star party to suitably gloomy weather, kicked off by a dinner and live music in the parking lot.  I’ve posted some pictures of the event including a last run through the museum to capture some artwork on the James Webb Space Telescope, and a rare picture of Mercury above Venus just over the corner of the museum building.

As far as the future of TXMOST, the goal is to continue looking for large corporate donors to support the building of a permanent location, and in the meantime possibly reopen on a smaller scale if a suitable location can be found.  There have been ongoing negotiations with the City of Cedar Park to provide the land for the permanent location, but without a suitable backing to build the building, the City has not been willing to officially commit the land.  So, if you’re here and reading this, certainly I’m sure TXMOST will appreciate anything you wish to donate, but you can also talk to your company HR and management to determine if your company has any sort of charitable outreach program that could get involved.  Many of us work for high tech companies who are reliant on finding employees with science, technology, engineering, and math backgrounds.  Certainly they should find value in helping to spark the interest in STEM in our next generations at an early age.  The future will thank you for it!

As far as the Friday night star parties, I am working on lining up a new location to be able to keep doing the star parties and keep up the awareness of TXMOST.  Watch here for more information on that.

Posted in Uncategorized | Leave a comment